GitLab

Detail:
  hdr/board - Definitions for GPIO values used to detect beagleboard revision
  s/Boot - Added code to detect BB revision via GPIO lines, in order to determine the correct setting for the TPS pin which controls the EHCI power
Admin:
  Tested on BB rev C2, BB-xM rev A2.
  BB xM rev C should work now!


Version 0.44. Tagged as 'OMAP3-0_44'

Detail:
  Makefile, s/KdbScan, hdr/StaticWS - Code to handle keyboard scanning, via the new HAL build of the USB drivers.
  s/Stubs - Removed old stub keyboard scan routines
  s/CPUClk - ADR -> ADRL to cope with new workspace layout
  s/Boot, s/Top, hdr/Post - Modified to use new HALSize variable for determining the HAL size. Trimmed dead code/definitions.
  s/Boot - FIQDebug code now copes with the different USER button GPIO used on the BB-xM
  s/board - Increased max pixel rate from 86.5MHz to 100MHz. This allows a wider range of screen modes to be used, although it is beyond the spec of the video controller, and not all boards will be able to reach 100MHz. This should match the value used in the initial ARMini units.
Admin:
  Tested on rev C2 BB, A2 BB-xM, C1 TouchBook
  Needs latest USB drivers, Kernel source, BuildSys & Env (not all of which have been checked in yet)


Version 0.43. Tagged as 'OMAP3-0_43'

Detail:
  s/I2C - The IIC driver now flushes the RX & TX FIFOs before each transfer. This ensures the correct data is sent/received following certain errors (e.g. NACK)
Admin:
  Tested on rev C1 TouchBook


Version 0.42. Tagged as 'OMAP3-0_42'

Detail:
  Makefile, s/CPUClk, hdr/CPUClk, s/Boot, hdr/StaticWS - Provide an implementation of the new HALDevice_CPUClk HAL device. Allows OMAP35x and DM37x CPU's to be set to any of the standard OPPs as listed in the datasheets. Doesn't yet support 1GHz on DM37x.
  hdr/NIC, hdr/PRCM, hdr/omap3530, s/TPS - Misc additions/tweaks/fixes.
Admin:
  Tested on rev C2 BB, A2 BB-xM, C1 TouchBook
  Requires latest PortableHAL & Kernel


Version 0.41. Tagged as 'OMAP3-0_41'

Detail:
  s/Boot - Added support for the new HAL_ExtMachineID call, and changed HAL_MachineID to return 0's
Admin:
  Tested on rev A2 BB-xM


Version 0.40. Tagged as 'OMAP3-0_40'

Detail:
  s/I2C - Changed HAL_Video_IICOp to call RISCOS_IICOpV instead of using its own polling based transfer loop. Updated IIC_DoOp_Poll to work with multiple buses.
  s/board - Allow the OS to see the video IIC buses now that any transfers on them will be using OS_IICOp's queueing/re-entrancy code
Admin:
  Tested on rev A2 BB-xM


Version 0.39. Tagged as 'OMAP3-0_39'

Detail:
  c/NVMem, c/fat, h/NVMem, h/common, h/fat - C code for reading a 'CMOS' file off the SD card on boot, for use as a CMOS RAM image
  c/CLib - Added extra functions needed by the SD/MMC driver
  s/NVMemory - Implementation of the HAL NVRAM API, for reading/writing the loaded CMOS file. The read/write functions handle RISC OS's CMOS address mangling, so that CMOS files saved by *SaveCMOS can be used as-is.
  hdr/StaticWS - Updated with workspace needed by the new code
  s/Boot - Initialise the CMOS cache on boot
  s/Stubs - Removed the stub NVRAM function
  Makefile - Added the new files
Admin:
  Tested on rev A2 BB-xM.


Version 0.38. Tagged as 'OMAP3-0_38'

Detail:
  s/RTC - RISC OS will set the time members and/or the date members of the RTCTimeStruct to -1 when it doesn't want them updating.
  So skip writing those entries to the RTC if they're not meant to be updated!
Admin:
  Tested on rev C2 beagle.
  Fixes issue reported on forums with setting date from BASIC:
  http://www.riscosopen.org/forum/forums/4/topics/521


Version 0.37. Tagged as 'OMAP3-0_37'

Detail:
  s/board - filled in the VideoGPIO entry for the IGEP. From looking at recent linux sources it's quite clear that GPIO 170 is used for enabling the DVI framer, and 24 is used for resetting the EHCI controller.
Admin:
  Tested-ish on rev C2 beagleboard by setting GPIO 170 (pre-xM video GPIO) to an input shortly after boot (i.e. to the default setting, as it would be on an IGEP).
  IGEP-like display failures then followed, but everything went back to normal when the GPIO was set back to being an output.


Version 0.36. Tagged as 'OMAP3-0_36'

Detail:
  s/GPIO - The IRQ settings for the DevKit8000's NIC were wrong and should have been active-low, not active-high. This fixes that.
Admin:
  Tested by Stephen Leary with his NIC driver


Version 0.35. Tagged as 'OMAP3-0_35'

Detail:
  s/Boot - HAL_Reset now sets the PRM_RSTCTRL.RST_DPLL3 bit instead of the PRM_RSTCTRL_GS bit. This matches what Linux does, and seems to fix resets on the TouchBook.
  s/board - Changed TouchBook audio to use the hands-free output instead of the predriver. This fixes speaker output (although it's currently listed as "line out" by the sound setup configure plugin)
  hdr/board, s/board, s/Video - Update the LCDConfig struct to contain an entry for controlling LCD power/brightness. Hook up basic power controls for current machine types.
Admin:
  Tested on rev C2 beagleboard & C1 touchbook.
  Video changes mean that OMAPVideo 0.08 or newer is required.


Version 0.34. Tagged as 'OMAP3-0_34'

Detail:
  hdr/board, s/board, s/Boot - Linux machine IDs are now defined via constants in hdr/board instead of magic numbers on a per-use basis
  s/Boot - Added video fix for BB-xM rev A3.
  s/Boot - Added code to enable tablet battery charging on TouchBook.
  s/Boot - Added support for power-off on TouchBook
  s/GPIO - Fixed bug in GPIOx_SetAsOutput that would prevent LEDs from being disabled properly
  s/I2C - Updated code to ignore BF interrupts. Added debugging code to help track down unexpected errors, and to check that IIC_DoOp_Poll is being called with interrupts disabled.
  s/SDMA - Call HAL_IRQClear when resetting the DMA controller device. This fixes the "previous IRQ not cleared" loop that would occur during RISC OS's pre-reset sequence
Admin:
  Tested on rev C2 beagleboard, C1 touchbook, A3 BBxM.
  Resets should now work reliably on all machines, except TouchBook, which still seems to hang. But on the bright side, the TouchBook is currently the only machine to support soft-off.


Version 0.33. Tagged as 'OMAP3-0_33'

Detail:
  s/board, hdr/board, hdr/omap3530, hdr/UART - Add support for 4th UART available on AM/DM37x (i.e. BeagleBoard-xM)
  hdr/omap3530 - Add details of CONTROL_IDCODE register & known hawkeye/revision numbers for OMAP type/revision detection
  s/Boot, s/GPIO, hdr/GPIO, s/I2C, hdr/StaticWS - Allow TPS LED drivers to be used as (output-only) GPIOs. Add new polled I/O I2C function, and appropriate logic to make GPIO code use it instead of RISCOS_IICOpV if RISC OS hasn't finished initialising yet. Add code to initialise some extra BB/TB GPIOs on boot.
  s/Timers, hdr/Timers - Stop RISC OS from using GPTIMER9, because it's used to drive the screen backlight on the TouchBook
  s/Video - Use appropriate porch/sync limits on non-OMAP35x
  s/PRCM - Don't mess with the system clock divider when calculating system clock speed (AM/DM37x fix)
Admin:
  Tested on rev C2 beagleboard, rev A2 BB-xM (indirectly), rev C1 TouchBook


Version 0.32. Tagged as 'OMAP3-0_32'

Detail:
  s/Boot - The FIQDebug code can now be used to trigger the DebugCallstack code when the user button is pressed
Admin:
  Tested on rev C2 beagleboard


Version 0.31. Tagged as 'OMAP3-0_31'

This time, put the GET directive in the right place, so it fixes all the compile errors and not just the ones AMU's dodgy dependency tracking reported

Version 0.30. Tagged as 'OMAP3-0_30'

Version 0.29. Tagged as 'OMAP3-0_29'

Update OMAP3 HAL to use correct instruction/memory barrier operations and to handle branch target predictors

Detail:
  hdr/Copro15ops - Added myISB, myDSB, myDMB macros to provide barrier functionality for ARMv6+
  s/Boot, s/Interrupts, s/RAM, s/Top, s/Video - updated to use correct barrier operations after CP15 writes, and to invalidate branch predictors where appropriate
Admin:
  Tested on rev C2 beagleboard


Version 0.28. Tagged as 'OMAP3-0_28'

Detail:
  hdr/Interrupts - moved MPU_INTC values into hdr/omap3530
  hdr/omap3530 - Revised L3_Size, L4_Size, etc. so that they indicate the size of the used area of the interconnects, rather than the size of the address space
  s/Boot - reworked HAL setup to take into account the fact that mapping in L4_Core no longer maps in L4_Wakeup and MPU_INTC. Also fixed DevKit NIC setup to request correct IO space size
Admin:
  Tested on rev C2 beagleboard. Should now use ~4MB of IO space instead of >=33MB


Version 0.27. Tagged as 'OMAP3-0_27'

Detail:
  s/GPIO - Fixed use of invalid 'MSR <psr>,<rn>,<shift>' instruction in GPIOx_SetAndEnableIRQ. Fixed PSR flags that are used to calculate LEVELDETECT0 value.
  s/NIC - Fixed NICActivate to load NICGPIO_Mode before the HAL device ptr gets clobbered
Admin:
  Tested on rev C2 beagleboard, using IGEP config. NICActivate now appears to configure the GPIO controller properly.


Version 0.26. Tagged as 'OMAP3-0_26'

Detail:
  s/Boot, s/GPIO - Added some basic GPIO init code, to make sure there aren't any unexpected GPIO IRQs active
Admin:
  Tested on rev C2 beagleboard.


Version 0.25. Tagged as 'OMAP3-0_25'

Detail:
  s/GPMC, hdr/GPMC, hdr/StaticWS - basic code to reset the GPMC and configure chip selects
  s/NIC, hdr/NIC, hdr/StaticWS - code to expose any onboard NICs (SMSC9221, DM9000) to RISC OS as simple HAL devices.
  Makefile - added GPMC & NIC source files
  s/board, hdr/board - Expanded board config struct to include a pointer to extra code to call at the end of HAL_InitDevices, to allow board-specific devices to be initialised
  s/boot - Extra HAL_InitDevices code to set up the NICs on the IGEP/DevKit
  s/GPIO, hdr/GPIO - Improved functionality to allow GPIO IRQs to be used
  s/SDMA, s/Video - Tweaked the HAL device descriptors to indicate that the devices are on the L3 interconnect
Admin:
  Tested on rev C2 beagleboard. IGEP/DevKit entry points booted OK, but no attempts were made to look for or interact with the new HAL devices!


Version 0.24. Tagged as 'OMAP3-0_24'

Detail:
  hdr/StaticWS, hdr/Video, hdr/board, hdr/omap3530, s/Boot, s/Video, s/board - Add new HALDoesVideo switch to control whether the HAL provides the video driver or whether a HAL device is used to expose the video hardware to the OMAPVideo module. Switch defaults to the 'off' state, i.e. OMAPVideo provides the video driver. Also updated the board config struct to contain more detailed information about the video capabilities of each board.
  s/Audio - fix the FIFO underflow/overflow IRQ handler to disable the IRQ after the underflow/overflow has been detection. This prevents the OS from (potentially) getting stuck in a loop servicing the interrupt and never reaching the state where it can shut down & re-initialise the audio to fix the error properly.
  s/Debug - add DebugCallstack function that disables IRQs/FIQs and dumps the stack contents over the serial port
Admin:
  Tested on rev C2 beagleboard.


Version 0.23. Tagged as 'OMAP3-0_23'

Detail:
  s/board - DevKit8000 USBGPIO setting has been changed from 255 (none) to GPIO 147.
  I'm still not convinced that GPIO147 is connected to anything, but if it works with that setting then we might as well use it.
Admin:
  Untested; but according to Tank it makes USB work.


Version 0.22. Tagged as 'OMAP3-0_22'

Various OMAP3 HAL power management improvements, plus add support for board config autodetection via Linux machine ID

Detail:
  s/board, hdr/board - Add Linux machine ID & available mixer channels to board config table
  s/Top - Add new entry point at offset &64, for booting as a fake Linux kernel. Searches the board config table until it finds a config matching the machine ID passed in R1. Also minor ROM copy optimisation, unsigned pointer comparison fixes
  s/Audio, hdr/Audio - Use board config to lock-out mixer channels that aren't connected to any hardware, to avoid excessive power drain or other problems if the channels get turned on. Also perform many other setting tweaks to tidy up default settings for unused mixer paths/channels.
  s/Video - Fix Video_Init logic when deciding whether to reset DSS, enable DSI PLL drift guard
  s/I2C - Increase I2C timeout values, since the previous values were perhaps a bit low
  s/Audio, s/I2C, s/Interrupts, s/RAM, s/SDMA, s/Timers, s/UART, hdr/UART, s/USB, s/Video - Enable autoidle/smart idle where possible to help save power.
Admin:
  Tested on rev C2 beagleboard


Version 0.21. Tagged as 'OMAP3-0_21'

Detail:
  PRCM.s - This file missed my checkin last night. Contains some rather important code that was moved there from USB.s, for initialising DPLL5.
Admin:
  Tested on rev C2 beagleboard. HAL code in CVS should now match what's on my machine!


Version 0.20. Tagged as 'OMAP3-0_20'

Update OMAP HAL to support different board configs, plus use new YearLOIsGood flag to ensure correct RTC handling, plus other misc tidying

Detail:
  The OMAP HAL now has multiple entry points, one per board config. See Top.s/board.s for more info.
  audio.s - Moved APLL_CTL value to board config
  board.s - New file to list all the settings for the different board configs
  boot.s - Change HAL_Init to deal with the new board config stuff
  debug.s - Debug UART now specified in board config
  GPIO.s - A few utility functions for handling OMAP/TPS GPIO pins
  I2C.s - Update to use new board config struct
  RAM.s - Disable the beagleboard-specific RAM init code. Instead we'll just rely on u-boot to initialise all our RAM for us.
  RTC.s - Get rid of the magic numbers, and use the YearLOIsGood flag to indicate to RISC OS that YearLO is 2-digit BCD
  Top.s - Got rid of old debug code and rewrote initial flow to handle detecting & storing the board config
  UART.s - Update to use board config struct, support multiple UARTs
  USB.s - Get EHCI PHY power GPIO from board config
  Video.s - Get DVI framer power GPIO and max pixel rate from board config. Add 'PassiveVideo' option, to build a driver that doesn't alter the video output settings - should hopefully result in a usable display on Touch Book, etc.
  board.hdr - Definition of board config table struct
  GPIO.hdr - Add lots of macros for handling OMAP GPIO pins, new constants for OMAP/TPS GPIO
  I2C.hdr - Added I2C transfer block struct, HAL I2C API transfer states (both moved here from other source files)
  omap3530.hdr - Move/remove some unwanted constants, disable DebugChar for now
  StaticWS.hdr - Move I2C transfer block struct to I2C.hdr, add board config struct to HAL workspace, get rid of unused 64K AllocArea
  Timers.hdr - Tidy up constants a bit
  UART.hdr - Add UARTCLK (moved from StaticWS.hdr), UART IRQ #'s
  Makefile - add GPIO.s
Admin:
  Tested on rev C2 beagleboard. Board configs for other board types may be inaccurate in a couple of places.


Version 0.19. Tagged as 'OMAP3-0_19'

Detail:
  hdr/Audio, s/Audio, Makefile, hdr/StaticWS, s/Boot - Add sound support to OMAP3 HAL. Should work with a TPS65950 connected to I2C1/McBSP2, as per beagleboard.
  s/TPS, s/RTC - Moved TPSRead, TPSWrite functions out of s/RTC and into their own file
  hdr/SDMA, s/SDMA - Add support for packet-based transfer (for audio), improve debug code, remove TestRAMToRAM test code
  s/I2C - Update to handle spurious RDR interrupts as mentioned in OMAP3 errata
  s/Video - Enable support for the larger porch & sync timing registers found in OMAP3 ES3.1 and above
Admin:
  Tested on rev C2 beagleboard


Version 0.18. Tagged as 'OMAP3-0_18'

Detail:
  I guess I didn't test this after all.
Admin:
  Tested on rev C2 beagleboard. (No, really, I mean it this time!)


Version 0.17. Tagged as 'OMAP3-0_17'

Detail:
  Boot.s - Make FIQDebug work again
  Boot.s - Add support for DMA & video devices
  Interrupts.s, hdr/omap3530 - Add 'ExtraDebugInterrupts' option
  hdr/SDMA, SDMA.s, Makefile - DMA code which presents itself to RISC OS as a set of single-buffered, interrupt-driven DMA channels.
  hdr/StaticWS - Add extra DMA, video & debug entries to workspace
  Interrupts.s - Add 'DebugDisablePrevious' debug option for more flexibility in tracking down noncleared IRQs with ExtraDebugInterrupts
  RAM.s - Use DMA to clear RAM on boot. RAM clear now takes less than 1 second on a rev C board, whereas before it used to take several.
  Video.s - Add simple HAL device to expose information needed by upcoming RISC OS module based video driver.
Admin:
  Tested on rev C2 beagleboard.


Version 0.16. Tagged as 'OMAP3-0_16'

Detail:
  The code which checks if you've just disabled the active interrupt was broken and was dereferencing a bad pointer, causing (a) bad things, and (b) failure when alignment exceptions are turned on. This change fixes that, so the change I checked in a couple of hours ago won't cause the OS to crash anymore!
Admin:
  Tested on rev C2 beagleboard.


Version 0.15. Tagged as 'OMAP3-0_15'

Detail:
  This implementation only supports resets - for power-off a more complex implementation will be required (involving talking to the TPS over I2C, AFAIK).
Admin:
  Tested on rev C2 beagleboard


Version 0.14. Tagged as 'OMAP3-0_14'

Detail:
  s/RTC - Implementation of new HAL RTC API. Uses the RTC built into the TWL/TPS companion chip.
  s/Boot - Initialise RTC HALDevice
  s/I2C - Add workaround for apparent hardware limitation of the OMAP I2C controllers; where appropriate multiple iic_transfers will now be merged together into one transfer, to ensure that a start bit is always sent at the start of each transfer
  hdr/omap3530 - Tweak DebugReg and DebugRegByte to allow LR to be output
  Makefile - add s.RTC to list of files. Fix GPADBG definition to not conflict with the 'gpa' folder that one of the makefile fragments creates.
Admin:
  Tested on rev C2 beagleboard


Version 0.13. Tagged as 'OMAP3-0_13'

Detail:
  Makefile, s/Boot, s/I2C, hdr/I2C, hdr/StaticWS - Adds I2C support to the OMAP3 HAL, via both HAL_IIC* and HAL_Video_IICOp.
  s/Interrupts - Fix bug causing incorrect clearing of FIQs
  s/Debug, s/Boot, hdr/omap3530 - Improve debugging code, and add simple FIQ debugger that outputs the PC to the serial port when the beagleboard USER button is pressed
  s/Stubs - Remove old stub functions
Admin:
  Tested on rev C2 beagleboard


Version 0.12. Tagged as 'OMAP3-0_12'

Detail:
  hdr/StaticWS, s/Boot - Store logical address of OTG controller
  hdr/USB, s/USB - Expose OTG controller by HAL_USBControllerInfo API
Admin:
  Tested on Rev C2 beagleboard


Version 0.11. Tagged as 'OMAP3-0_11'

Detail:
  CPU version is no longer specified in the makefile - it's better to inherit
  it from the build environment now that we actually set it appropriately.
Admin:
  Built and briefly tested.

Version 0.10. Not tagged

Detail:
  Uses suffixed file extensions for compatiblity with both objasm and asasm.
Admin:
  Supplied by Peter Naulls, tested at ROOL

Version 0.10. Not tagged

Detail:
  hdr/StaticWS - Add entries for max porch & sync values, in anticipation of future OMAP revisions increasing the limits from 8/6 bits to 12/8 bits.
  hdr/omap3530 - Add entry for CONTROL_IDCODE register for reading silicon revision
  s/Video - Increase max pixel rate from 65MHz to 75MHz (86.5MHz seems unstable). Add support for different max porch/sync values depending on hardware revision (currently disabled). Make mode change code more robust to try and fix corruption seen when changing mode too many times. Improve HAL_Video_VetMode to check for (HFP+HSW+HBP)*PCD > 8 limitation. Add a bit more debug code.
Admin:
  Tested on rev C2 beagleboard.


Version 0.10. Tagged as 'OMAP3-0_10'

Detail:
  s/Video - Rewritten pointer image update code to correctly read data from RISC OS's 32 pixel wide cursor buffer.
Admin:
  Tested on rev C2 beagleboard. Hourglass now appears properly!


Version 0.09. Tagged as 'OMAP3-0_09'

Detail:
  Makefile - added USB to objects list
  s/Boot, s/USB, hdr/StaticWS, hdr/USB - USB EHCI code
  s/Debug, s/Stubs, s/Timers, s/Top, s/UART, s/Video - Debugging tweaks and header dependency fixes
  s/Interrupts, hdr/omap3530 - Interrupt fixes & debugging code
  hdr/PRCM - typo fix
Admin:
  Tested on rev C2 beagleboard


Version 0.08. Tagged as 'OMAP3-0_08'

Detail:
  s/Top - Fix cache clean code to iterate sets/ways/cache levels correctly
Admin:
  Tested on rev C2 beagleboard


Version 0.07. Tagged as 'OMAP3-0_07'