GitLab

Detail:
  ECFIndex and PalIndex claim to be mode variables, but it's impossible for extension modes to specify their values.
  Since they're easy to calculate from the ModeFlags and Log2BPP values, drop them from the mode workspace (+ table of builtin modes) and calculate them on the fly instead.
  File changes:
  - hdr/KernelWS - Drop ECFIndex & PalIndex from workspace
  - s/vdu/vdumodes - Adjust workspace definition, drop ECFIndex & PalIndex values from VWSTAB
  - s/vdu/vdudriver - Remove now-redundant copy loop from ModeChangeSub. Remove code from GenerateModeSelectorVars that sets up the ECFIndex & PalIndex values on the stack
  - s/vdu/vdugrafl - Adjust copy loop in SwitchOutputToSprite/Mask
  - s/vdu/vdupalette, s/vdu/vdupalxx - Add GetPalIndex routine to generate PalIndex on the fly. Drop the obsolete 16bpp palette/gamma table and shuffle the other entries to simplify GetPalIndex a bit.
  - s/vdu/vduplot - Add GetECFIndex routine to generate ECFIndex on the fly. Also, fix things so that mode 0 isn't the only rectangular-pixel mode which uses the special rectangular-pixel ECF patterns (index 0 vs. index 4). Fiddle with ExportedHLine a bit to avoid an out-of-range ADR.
  - s/NewReset - Fix UAL warning for MOV R0, AppSpaceStart. Adjust memset to not assume 512KB is the correct amount
Admin:
  Tested on Raspberry Pi 3


Version 6.11. Tagged as 'Kernel-6_11'

Detail:
  This change gets rid of the following switches from the source (picking appropriate code paths for a 32bit HAL build):
  * HAL
  * HAL26
  * HAL32
  * No26bitCode
  * No32bitCode
  * IncludeTestSrc
  * FixR9CorruptionInExtensionSWI
  Various old files have also been removed (POST code, Arc/STB keyboard drivers, etc.)
Admin:
  Identical binary to previous revision for IOMD & Raspberry Pi builds


Version 5.49. Tagged as 'Kernel-5_49'

Expand tabs.
Swap DCI for instructions now Objasm 4 is out.
Symbols for FSControl_CAT/RUN/OPT changed to non Arthur definitions.
Still boots on IOMD class, no other testing.

Version 5.35, 4.79.2.124. Tagged as 'Kernel-5_35-4_79_2_124'

Detail:
  s/Arthur3, s/ChangeDyn, s/HAL, s/HeapMan, s/Middle, s/MoreSWIs, s/NewIRQs, s/Utility, s/VMSAv6, s/PMF/key, s/PMF/osbyte, s/PMF/osword, s/vdu/vdudecl, s/vdu/vdudriver, s/vdu/vduplot, s/vdu/vduwrch - Tweaked lots of LDM/STM instructions in order to get rid of the depracation/performance warnings
Admin:
  Tested on rev A2 BB-xM


Version 5.35, 4.79.2.98.2.53. Tagged as 'Kernel-5_35-4_79_2_98_2_53'

Detail:
 * Stopped calling the broken abort fixup code when running under VMSAv6.
   Might be desirable to update it, possibly farmed out to a separate module -
   still need to think about this.
 * Unaligned load optimisations can now be disabled by the global NoUnaligned
   flag for testing purposes.
 * Extended OS_ReadUnsigned to permit reading of 64-bit unsigned integers.
   See Docs.ReadUnsigned for more details. Also sped it up by using MLA
   (or UMLAL) for most digits rather than repeated addition.
 * Bugfix is OS_GSRead: an uninitialised r0 was being passed to
   OS_ReadUnsigned, causing undesirable effects on rare occasions.
Admin:
  Tested on a rev B7 beagleboard.

Version 5.35, 4.79.2.98.2.8. Tagged as 'Kernel-5_35-4_79_2_98_2_8'

Detail:
  Having scanned the kernel source for unaligned load code fragments which
  would abort on ARMv6 and v7 and not having found any, I took the opportunity
  to give them build-time switches to use unaligned LDR((S)H)/STR(H)
  instructions if built for a new enough platform. Also added a couple of
  cases of LDRSB that will benefit v4 CPUs and a few instances of the v6
  SXTH instruction, but since objasm doesn't yet understand it (and when it
  does, not everyone will have upgraded) they are currently written as
  DCI statements.
  Most of the changes are to OS_Word handlers, which are notorious in that
  their input/output block is not word-aligned.
Admin:
  Not tested, but it should at least build.

Version 5.35, 4.79.2.98.2.6. Tagged as 'Kernel-5_35-4_79_2_98_2_6'

Added "fast" flash tool for Customer L, allowing ROMs to be sent serially at
115200 baud not 9600 baud.
Fix to VDU despatch for ARMv4 and later.
Fixes to power on delete keyboard and keyboard timeout
Implemented MemoryReadPhys and MemoryAmounts with the HAL.

Version 5.35, 4.79.2.59. Tagged as 'Kernel-5_35-4_79_2_59'

Version 5.35, 4.79.2.48. Tagged as 'Kernel-5_35-4_79_2_48'

* Added ARM_IMB and ARM_IMBRange SWIs as recommended by ARMv5.
* Some early prototype HAL bits popped in - a lot of source restructuring still
  to come.
* New debug target creates an AIF image with debug information, and translates
  this into an ASCII object file for the 16702B logic analyser.

Version 5.35, 4.79.2.1. Tagged as 'Kernel-5_35-4_79_2_1'

Details:
  The Kernel will now compile to produce a pure 32-bit system if No26bitCode is
  set to TRUE.
  If No26bitCode is FALSE, then the Kernel will be a standard 26-bit Kernel,
  although some internal changes have taken place to minimise compile
  switches between the two cases. See Docs.32bit for more technical info.

  The hardest part was the flood-fill...

Other changes:
  Pointer shape changes now take place on the next VSync, rather than actually
  WAITING for the VSync. Turning the Hourglass on shouldn't slow your machine
  down by 5% now :)

  Lots of really crusty pre-IOMD code removed.

Admin:
  Tested in 32 and 26-bit forms in a limited desktop build. Basically, this
  will need to see a lot of use to iron out difficulties. I'd like anyone who
  has a non-frozen project to at least attempt using this Kernel.

Version 5.23. Tagged as 'Kernel-5_23'