GitLab

Version 1.00. Tagged as 'OMAP3-1_00'

- Comments and symbolic names for RTC register bits copied over from OMAP4 sources.
- Delete dead function ReadTimeForNVRAM.
- Use RTCFormatFlags_BCD_NeedsYearHelp flag for year 2070 compatibility.
- Moved CallOS macro into a header.
Tested on a Beagleboard xM, clock still worked over a power cycle.

Version 0.90. Tagged as 'OMAP3-0_90'

To help OMAP4 tracking changes a number of the changes were purely cosmetic lining up differences, this change is where OMAP3 wasn't on a conventional column layout.

Version 0.61. Tagged as 'OMAP3-0_61'

Harder than it should have been because someone wired the reset button up to the cold reset pin.
Now gets the OSStartFlags right so that delete-power-on et al are respected by the kernel.

Version 0.57. Tagged as 'OMAP3-0_57'

Detail:
  hdr/board, s/board, s/Boot - Linux machine IDs are now defined via constants in hdr/board instead of magic numbers on a per-use basis
  s/Boot - Added video fix for BB-xM rev A3.
  s/Boot - Added code to enable tablet battery charging on TouchBook.
  s/Boot - Added support for power-off on TouchBook
  s/GPIO - Fixed bug in GPIOx_SetAsOutput that would prevent LEDs from being disabled properly
  s/I2C - Updated code to ignore BF interrupts. Added debugging code to help track down unexpected errors, and to check that IIC_DoOp_Poll is being called with interrupts disabled.
  s/SDMA - Call HAL_IRQClear when resetting the DMA controller device. This fixes the "previous IRQ not cleared" loop that would occur during RISC OS's pre-reset sequence
Admin:
  Tested on rev C2 beagleboard, C1 touchbook, A3 BBxM.
  Resets should now work reliably on all machines, except TouchBook, which still seems to hang. But on the bright side, the TouchBook is currently the only machine to support soft-off.


Version 0.33. Tagged as 'OMAP3-0_33'

Detail:
  s/GPMC, hdr/GPMC, hdr/StaticWS - basic code to reset the GPMC and configure chip selects
  s/NIC, hdr/NIC, hdr/StaticWS - code to expose any onboard NICs (SMSC9221, DM9000) to RISC OS as simple HAL devices.
  Makefile - added GPMC & NIC source files
  s/board, hdr/board - Expanded board config struct to include a pointer to extra code to call at the end of HAL_InitDevices, to allow board-specific devices to be initialised
  s/boot - Extra HAL_InitDevices code to set up the NICs on the IGEP/DevKit
  s/GPIO, hdr/GPIO - Improved functionality to allow GPIO IRQs to be used
  s/SDMA, s/Video - Tweaked the HAL device descriptors to indicate that the devices are on the L3 interconnect
Admin:
  Tested on rev C2 beagleboard. IGEP/DevKit entry points booted OK, but no attempts were made to look for or interact with the new HAL devices!


Version 0.24. Tagged as 'OMAP3-0_24'

Various OMAP3 HAL power management improvements, plus add support for board config autodetection via Linux machine ID

Detail:
  s/board, hdr/board - Add Linux machine ID & available mixer channels to board config table
  s/Top - Add new entry point at offset &64, for booting as a fake Linux kernel. Searches the board config table until it finds a config matching the machine ID passed in R1. Also minor ROM copy optimisation, unsigned pointer comparison fixes
  s/Audio, hdr/Audio - Use board config to lock-out mixer channels that aren't connected to any hardware, to avoid excessive power drain or other problems if the channels get turned on. Also perform many other setting tweaks to tidy up default settings for unused mixer paths/channels.
  s/Video - Fix Video_Init logic when deciding whether to reset DSS, enable DSI PLL drift guard
  s/I2C - Increase I2C timeout values, since the previous values were perhaps a bit low
  s/Audio, s/I2C, s/Interrupts, s/RAM, s/SDMA, s/Timers, s/UART, hdr/UART, s/USB, s/Video - Enable autoidle/smart idle where possible to help save power.
Admin:
  Tested on rev C2 beagleboard


Version 0.21. Tagged as 'OMAP3-0_21'

Detail:
  hdr/Audio, s/Audio, Makefile, hdr/StaticWS, s/Boot - Add sound support to OMAP3 HAL. Should work with a TPS65950 connected to I2C1/McBSP2, as per beagleboard.
  s/TPS, s/RTC - Moved TPSRead, TPSWrite functions out of s/RTC and into their own file
  hdr/SDMA, s/SDMA - Add support for packet-based transfer (for audio), improve debug code, remove TestRAMToRAM test code
  s/I2C - Update to handle spurious RDR interrupts as mentioned in OMAP3 errata
  s/Video - Enable support for the larger porch & sync timing registers found in OMAP3 ES3.1 and above
Admin:
  Tested on rev C2 beagleboard


Version 0.18. Tagged as 'OMAP3-0_18'

Detail:
  Boot.s - Make FIQDebug work again
  Boot.s - Add support for DMA & video devices
  Interrupts.s, hdr/omap3530 - Add 'ExtraDebugInterrupts' option
  hdr/SDMA, SDMA.s, Makefile - DMA code which presents itself to RISC OS as a set of single-buffered, interrupt-driven DMA channels.
  hdr/StaticWS - Add extra DMA, video & debug entries to workspace
  Interrupts.s - Add 'DebugDisablePrevious' debug option for more flexibility in tracking down noncleared IRQs with ExtraDebugInterrupts
  RAM.s - Use DMA to clear RAM on boot. RAM clear now takes less than 1 second on a rev C board, whereas before it used to take several.
  Video.s - Add simple HAL device to expose information needed by upcoming RISC OS module based video driver.
Admin:
  Tested on rev C2 beagleboard.


Version 0.16. Tagged as 'OMAP3-0_16'